---
title: "ABV calculator, with fruit and sugar added along the way"
description: "Work out a homebrew’s ABV, attenuation and calories from hydrometer readings, including fruit or sugar added during fermentation."
url: https://www.fisherforbesbrewing.com/tools/abv-calculator/
publisher: Fisher & Forbes Brewing Co (https://www.fisherforbesbrewing.com)
---

# ABV calculator, with fruit and sugar added along the way

Enter your original and final gravity for the strength, how much of the sugar the yeast ate, and roughly how many calories are in a glass. Added fruit or sugar part way through? Add the readings either side of it and they’re counted too.

The calculator itself works on the page: ABV calculator.

## How it works

Strength comes from the drop in gravity: (OG − FG) × 131.25 gives the ABV as a percentage. It’s the formula most homebrewers use, and it’s accurate to within a few tenths for beers and wines of normal strength.

Fruit or sugar added during fermentation brings more sugar for the yeast, which a simple OG and FG miss. A reading just before the addition and another just after show how much it added: the rise is counted as if it had been in the original gravity.

Attenuation is the share of the sugar the yeast fermented: (OG − FG) ÷ (OG − 1). Calories come from the standard brewing formula, from the alcohol (7kcal a gram) and the sugars left behind (4kcal a gram).

## From our brews

Zing, our soured double IPA, started at 1.056. On day 11 it read 1.012, then 4.5kg of mango, pineapple and papaya took it back up to 1.016, and it finished at 1.006. OG and FG alone say 6.6%; counting the fruit, it’s 7.1%.

Pilot Episode went from 1.052 to 1.011: 5.4% ABV, 79% attenuation, and about 240kcal in a 500ml bottle.

## Questions

### Why does my ABV look low after adding fruit?

Because the fruit’s sugar never shows in your original gravity. Take a reading just before you add it and another once it’s stirred in, and put both into the calculator.

### How accurate is the 131.25 formula?

For most beers it’s within about 0.2%. Very strong beers and wines can read a little low; the figure is an estimate either way, as hydrometers are only as precise as the reading.

### Can I use it for wine or cider?

Yes. A wine finishing below 1.000 is fine; attenuation will read over 100%, which is normal for a dry wine, as alcohol is lighter than water.

### What’s the difference between original and final gravity?

Original gravity is your reading before the yeast goes in: how much sugar is in the wort. Final gravity is the reading once fermentation has finished. Yeast turns sugar into alcohol and CO₂, so the gravity falls, and how far it falls tells you how strong the beer is.

### How do I know fermentation has finished?

Take a gravity reading, then another two or three days later. If they match, it’s done. Bubbles in the airlock slowing down aren’t enough on their own: fermentation can stall and start again.

### Do I need to correct my hydrometer for temperature?

Yes, if your sample is much warmer or cooler than the temperature your hydrometer is calibrated to (usually 20°C, printed on it or its packet). Hot wort reads low, so either cool the sample first or put it through our hydrometer temperature correction calculator before you use the reading here.

### What does attenuation mean?

How much of the sugar the yeast ate, as a percentage. Most ale yeasts land somewhere between 65% and 85%; a stuck fermentation shows up as attenuation that’s much lower than the yeast should manage.

### How are the calories worked out?

From the same two readings: the alcohol the yeast made and the sugar it left behind both carry calories. It’s an estimate, as the formula assumes a typical beer, but it’s a fair guide to what’s in a glass.

---

Source: https://www.fisherforbesbrewing.com/tools/abv-calculator/
